Operating Tips for VHF SOTA

Bob K0NR SOTA Joyce K0JJWHere are some operating tips that I have found useful when doing Summits On The Air (SOTA) on VHF. I’ve been using VHF and higher frequencies for SOTA exclusively and have activated over 100 summits in Colorado (and other states such as California, Wyoming, New Mexico, North Carolina and Tennessee.)

The challenge with VHF and higher is that the radio range is limited compared with HF. (It really does help to bounce those signals off the ionosphere.) VHF propagation will vary depending on a lot of factors but for SOTA activations our range is typically 50 to 100 miles. In the backcountry of Colorado, a 50 mile radius may not include very many active radio amateurs, so you may come up short in terms of radio contacts. For your first activation(s), you may want to stay close to a metropolitan area.

First, take a look my blog posting about the basics: How To Do a VHF SOTA Activation

Next, here are some additional tips to having a successful activation:

Send Invitations

Get the word out to people that may be within range. I try to keep track of who I’ve worked in the past or know to be in a particular area and let them know when I’ll be activating. In some cases, I’ll go ahead and make a specific sked with a station. That is, we’ll meet on a particular frequency at a particular time, perhaps on CW or SSB for maximum weak signal performance.

Create an Alert and then Spot yourself on the sotawatch.org web page (using smartphone app).

Make Your Call

By the rules, SOTA contacts are always simplex, so on 2 meters the place to try is usually 146.52 MHz, the National Simplex Calling Frequency. (Some areas have established other 2m simplex frequencies to use for SOTA, so inquire locally.) This is the place to try calling.

Who are you going to find there? Hard to say. SOTA chasers will often listen to “five two”…that’s where they find SOTA activators. Also, there are radio hams that just like to hang out on 52…they like 2m FM operating but they don’t like repeaters so they listen here. You will also find that many mobile stations monitor 146.52 as they drive through rural areas. Basically, they are listening for anyone around but aren’t flipping from repeater to repeater as they change location. I’ll often hear 4WD enthusiasts, hikers, boaters, campers, etc. using Five Two.

We usually say something short and sweet one operating FM repeaters (“K0NR Monitoring”) but for SOTA we need to make a longer call. Realize that not everyone knows about SOTA so they may not know what the heck you are doing. Make a call such as this: “CQ CQ this is Kilo Zero November Romeo operating from Pikes Peak – Summits On The Air – anyone around?” Or “CQ 2 meters this is K0NR on Pikes Peak – Summits On The Air.” Do a little bit of “selling” when you make your call. Sound like you are having fun.

Sometimes people have their radios to set to scan multiple frequencies with 146.52 MHz set as one of the channels. If your transmission is too short, they will miss it. Also, it is helpful to mention the frequency you are calling on…sometimes I’ll say “CQ Five Two This is Kilo Zero November Romeo…”

Be Patient

Be patient. Sometimes it just takes time to accumulate your 4 QSOs to qualify for activator points. The few times I have been skunked on QSOs were when I did not have enough time, usually because storms were moving in. Keep calling every few minutes, taking a break once in a while to enjoy the view.

Try Other Frequencies

You may want to try other simplex frequencies, so know the band plan for the area you are activating in. Another trick is to get on a local 2m repeater and ask for someone to move over to simplex to work you. I have not had to do this very often but it does work. Have some of the local repeaters programmed into your radio.

Most of the SOTA VHF activity is on the 2 meter band, so that will be the “go to” band for most activations. However, it is fun to try other bands such as 6m and 70cm. I’ve been playing around with 1.2 GHz also (23 cm).

Improve Your Station

Hopefully by now you know that using an HT with a rubber duck antenna is a bad idea. Get at least a half-wave vertical or roll-up j-pole antenna. Better yet, get a small yagi antenna to add 5 or 6 dB to your signal. It can make a big difference on who you can work.  I’ve even started carrying a small 2m/70cm transceiver to get my 2m transmit power up to 30W. The objective is to extend your operating range.

Another angle is to use SSB and CW, which are much better for weak signal performance (compared to FM). This sets you up to work the serious VHF stations which tend to use these modes and have large high-gain antennas (horizontally polarized). Think about extending the range of your communications from a 50 mile radius to 200 miles, what a difference! (My best 2m distance on SOTA is 229 miles, using 2m CW on Capulin Mountain.)

73, Bob K0NR

6 Replies to “Operating Tips for VHF SOTA”

    • Alejandro,
      I am pleased to have you translate my blog posting! Thanks!
      There may be differences in VHF operating practices in Argentina. For example, is there a standard 2m FM calling frequency in LU and is it 146.52 MHz? It may be different.

      73 Bob

      • Hi Bob! Thanks. Here 146520 is used as preferred simplex call frequency also. One diffence is that almost everyone uses FM, there is none SSB activity on VHF here.

        Best Regards!
        LU1MAW Alejandro

  1. I get so many questions about the viability of VHF for SOTA, mostly from newer hams. VHF is very efficient if done right and you certainly pointed out some of the tricks of the trade to help ensure success. Nice job Bob and I found you on Twitter too. KG6HQD – Jerry

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.